PSU-LAB switching PSU repair
PSU · LAB · interactive reference

Switching Power Supply
Repair

A working tool for those who repair PSUs rather than replace them wholesale: interactive block diagrams, a voltage map by wire color, power calculations per rail, and a breakdown of 80 PLUS certifications.

Diagnostic order

Where to start

  • Visual inspection: bulging capacitors, heat marks, cracked solder joints on power leads.
  • Continuity check: fuse, varistor, rectifier bridge, and power switches (with shunt paths taken into account).
  • Standby +5VSB: without it the PWM never starts and PS_ON does nothing.
  • Force-start: PS_ON# (green) to COM. Watch for gate drive signals.
  • Load test with lamps or an electronic load, oscilloscope on outputs — check ripple and HF ringing.
Safety

Before you open it

Bulk capacitors hold up to 400 V after unplugging from mains. Discharge them with a 10–20 kΩ / 5 W resistor, not a screwdriver.
  • Work through an isolation transformer, especially when an oscilloscope is connected.
  • Never touch power switch heatsinks: they may sit at "hot ground" potential.
  • After repair — always verify no-load and full-load behavior before installing.
  • Cheap "no-name" units rated 700 W with a 400 W transformer are not a repair — they are a gamble.
Interactive schematic

Block diagram of a switching PSU (ATX)

Click any block to see its description, what to test, and its typical failure. Toggles on the right highlight suspect nodes and auxiliary paths.

no node selected

Pick a block on the schematic

Clicking a node will show its function, the components inside it, and what to inspect during repair.

    Voltage map

    24-pin ATX connector: color → voltage → purpose

    The switch changes pin labels. Click a pin or a color card to see details in the panel below.

    no pin selected

    Select a pin or a color

    Voltage, current rating, purpose of the line, and what to check during continuity testing will appear here.

      Other connectors

      ConnectorWiresVoltageCurrent per pinTypical use
      Molex 4-pin (peripheral)yellow / black ×2+12 Vup to 8 AFans, fan controllers, older HDDs
      Molex 4-pinred / black ×2+5 Vup to 8 ALegacy drives, lighting
      SATA poweryellow / red / orange+12 / +5 / +3.3 Vup to 4.5 ASSDs, HDDs, 2.5" drives
      PCIe 6-pinyellow ×3 + COM ×3+12 Vup to 8 A (75 W)Mid-range GPUs
      PCIe 8-pin (6+2)yellow ×3 + COM ×5+12 Vup to 8 A (150 W)GPUs, up to 2–3 per PSU
      EPS 8-pin (CPU)yellow ×4 + COM ×4+12 Vup to 8 A (235 W)CPU 4+4 power
      12VHPWR / 12V-2×6+12 V ×6 pairs+12 Vup to 9.5 AGPUs 300–600 W
      Cross-load rule: modern PSUs put most of their power on +12 V. If +5 V and +3.3 V together exceed ~120–130 W, a group-regulated unit may sag on +12 V — a common cause of false shutdowns.
      Calculation

      Power per rail and AC input draw

      Adjust sliders to match real-world load. The calculation accounts for −12 V (0.5 A) and standby +5VSB (2.5 A).

      Load per rail
      45 A
      15 A
      15 A
      Efficiency class (50 % load)
      Result
      +12 V 540 W
      +5 / +3.3 V 124 W
      Total DC 683 W
      AC input 759 W
      Heat loss 76 W
      AC current @ 230 V 3.5 A

      Rated power reference

      Rating+12 V+5 V+3.3 V5VSBTypical use
      300 W18–20 A15 A15 A2 AOffice, HTPC, no discrete GPU
      450 W30–34 A18 A18 A2.5 ABudget gaming, GTX 1650 class
      550 W42–45 A20 A20 A2.5 AMid-range gaming, RTX 4060
      650 W50–54 A20 A20 A3 AMid-plus gaming builds
      750 W62 A22 A22 A3 AHigh-end gaming, RTX 4070 Ti / 4080
      850 W70 A22 A22 A3 AHi-end, RTX 4090 stock
      1000–1200 W83–100 A25 A25 A3.5 AEnthusiast, SLI, overclocking, workstations
      Don't be fooled: in group-regulated designs the combined +5 V and +3.3 V output is almost always capped by a shared limit (typically 100–130 W), not by the sum of the individual rail ratings.
      80 PLUS

      Grouped by certification

      Efficiency shown at 20 / 50 / 100 % load. The switch changes the test standard — at 230 V numbers are noticeably higher.

      Comparison table

      Class20 %50 %100 %PFCTopologyRectifier